Leaking Pipe? What to Do First
Stop the water, protect the house, then find the leak: the first ten minutes, common causes, and how hidden pipe leaks are located without breaking walls.
A leaking pipe ranges from a drip under the kitchen sink to water bubbling up through a driveway. The first steps are the same either way: stop the water, protect the property, then work out where the leak actually is. That last part is often harder than it sounds, because most pipes in a South African home are hidden in walls, under floors or underground.
The First Ten Minutes
- Close the main isolating valve. It is usually near the water meter at the boundary, or where the supply pipe enters the house. Turn it clockwise until it stops.
- If water is near electrics, switch off at the distribution board before you touch anything.
- Open a cold tap at the lowest point in the house to drain the pressure out of the pipes.
- If the leak is on the hot side, switch off the geyser and close the cold supply valve into it.
- Photograph everything before cleaning up, if you may claim from insurance.
If you can't find or turn the isolating valve, that is worth fixing as soon as the emergency is over. Every home should have a working one that you can reach.
Visible Leaks: Common Causes
- Compression fittings and connectors under sinks and basins, which loosen or crack with age
- Flexible hoses to taps, toilets and appliances, which perish and burst
- Corroded galvanised pipe in older homes, usually failing at threaded joints
- Pinholes in copper pipe, often on hot-water lines
- Frost-damaged pipes on exposed outside runs after a cold Highveld night
Small visible leaks on fittings are often a quick repair. Corroded or repeatedly leaking pipe usually means a section needs replacing.
Hidden Leaks: How to Tell You Have One
Most leaking pipes are never seen. The signs are indirect:
- The water bill rises with no change in how you use water
- The water meter turns with every tap closed
- Damp patches, bubbling paint or swollen skirtings
- Warm spots on a tiled floor (a hot-water pipe below)
- Cracks in paving, or a patch of lawn that is always green or soggy
- Low water pressure, or the sound of running water when everything is off
The meter test
Close every tap, switch off irrigation and the pool top-up, read the meter, and read it again after 30 to 60 minutes without using water. Any movement means water is escaping on your side of the meter.
Then narrow it down. Close the valve to the geyser and test again: if the meter stops, the leak is on the hot side. Check toilets by putting a few drops of food colouring in each cistern; if colour appears in the bowl without flushing, the cistern is leaking.
Finding a Hidden Pipe Leak Without Breaking Things
Guessing where a hidden leak is usually means opening walls, tiles or paving in the wrong place. Professional leak detection finds it from the surface:
- Acoustic listening picks up the sound of water escaping under pressure, especially on metal pipe.
- Tracer gas is pushed into the pipe and rises through soil, paving and screed exactly where the pipe is open. It works on plastic pipe, which carries little sound.
- Thermal imaging shows the path of hot water escaping under floors and inside walls.
- Pressure testing confirms which section of the system is losing water.
The leak is then marked, so the repair needs only a small opening. Our water leak detection service covers all four, and our high water bill guide has more checks you can do first.
Repair or Replace?
A single leak on otherwise sound pipe is usually repaired with a short new section. If the pipe is badly corroded, or leaks keep appearing on the same run, replacing that run, often with a new route that avoids the slab, is cheaper in the long run. A good plumber will show you the condition of the pipe and quote both options.
Frequently Asked Questions
Q: Can I use tape or a clamp on a leaking pipe? A: As a temporary fix on a visible pipe, a repair clamp or self-fusing tape can slow a leak until a plumber arrives. It is not a permanent repair, and it won't work on pipes under pressure for long.
Q: Who is responsible for a leak before the water meter? A: Pipes on the municipal side of the meter are usually the municipality's to repair. Report the leak to your municipality; a leak detection report showing the leak is before the meter supports the report.
Q: How quickly should I deal with a hidden leak? A: As soon as you can. Water escaping underground or under a slab keeps costing money and can damage foundations, floors and walls the longer it runs.
Q: Does insurance pay for a leaking pipe? A: Many policies cover the resulting damage and sometimes the cost of finding the leak, but not the worn pipe itself. Check your policy and keep all photos and reports.
