Geyser Leaking? What to Do Right Now
Ceiling leak, dripping overflow, or a geyser that never stops heating: what each one means, what to switch off first, and how hidden hot-water leaks are found.
A leaking geyser is one of the most common plumbing problems in South African homes, and one of the most expensive to ignore. Every litre of hot water that escapes has already been paid for twice: once for the water, and once for the electricity to heat it.
But "the geyser is leaking" can mean several quite different things. Water dripping from the overflow pipe outside is not the same as water pouring through the ceiling, and neither is the same as a geyser that simply never stops heating. This guide covers what to do immediately, and how to work out which problem you have.
If Water Is Coming Through the Ceiling: Do This First
- Switch off the geyser at the distribution board. Find the breaker marked "geyser" and switch it off. Never touch wet electrical fittings.
- Close the cold-water supply to the geyser. There is usually an isolating valve on the cold pipe going into the geyser, often in the roof space. If you can't reach it safely, close the main isolating valve for the house.
- Open a hot tap somewhere in the house. This relieves the pressure in the system and slows the leak.
- Protect what is below: move furniture and electronics, and put down buckets and towels.
- Call your insurer if there is damage, and take photos before anything is cleaned up.
A burst geyser is a plumber's job, and in South Africa a geyser replacement must be installed to the national standard (SANS 10254) and certified by a registered plumber.
Water Dripping From the Overflow Pipe Outside
A geyser has safety valves that release water if the pressure or temperature gets too high. Their discharge pipes usually end outside, often through the eaves or a wall.
- A small drip while the geyser is heating is usually the expansion relief valve doing its job. Water expands as it heats, and a little discharge is normal.
- A constant trickle or steady flow, day and night, means a valve is not sealing or the pressure in the system is too high. It wastes a surprising amount of water and should be checked by a plumber.
No Visible Leak, But the Geyser Never Stops Heating
This is the one people miss. If your geyser switches on during the night when nobody is using hot water, or your electricity bill has crept up along with your water bill, hot water may be escaping through a leak on the hot-water pipes somewhere in the house.
Hot-water pipes run under tiled floors, inside walls and through the roof. A pinhole leak on one of them may never show as a wet patch. Signs to look for:
- Warm spots on a tiled floor, especially along a line from the geyser to a bathroom or kitchen
- Damp skirting boards or bubbling paint low on a wall
- A hissing sound when the house is quiet
- The water meter turning with every tap closed
A quick test you can do yourself
- Close every tap and make sure nothing is using water.
- Read the water meter, wait 30 minutes, and read it again.
- If it moved, close the cold supply valve to the geyser and repeat.
If the meter stops when the geyser supply is closed, the leak is on the hot-water side. If it keeps moving, the leak is somewhere on the cold side, such as the mains or a toilet cistern.
How a Hidden Hot-Water Leak Is Found
You don't need to start breaking tiles to find out where the water is going. Specialist leak detection uses:
- Thermal imaging, which shows the path of escaping hot water under tiles and inside walls as a warm plume
- Acoustic listening, which picks up the sound of water escaping under pressure from copper pipe
- Pressure testing and isolation, which confirms which section of pipe is losing water
Once the leak is marked, the repair usually needs just a few tiles lifted, rather than a trench along the whole pipe. Our water leak detection service covers this, and for geyser replacement and other plumbing work, see general plumbing.
Does Insurance Cover a Leaking Geyser?
Most South African home insurance policies cover a burst geyser and the resulting damage, usually with an excess. Cover for slow leaks and for finding hidden leaks varies a lot between policies. Read your policy wording, report the claim promptly, and keep the leak detection report: it documents what failed and where. Our guide on documenting a water leak for an insurance claim has more detail.
Frequently Asked Questions
Q: Is a dripping overflow pipe dangerous? A: A small drip while the geyser heats is normal. A constant flow is not dangerous in itself, but it wastes water and means a valve or the system pressure needs attention, so have it checked.
Q: How much water can a hidden hot-water leak waste? A: Even a small pinhole leak running day and night can lose hundreds of litres a day, and every litre of it has been heated. That is why a hot-water leak often shows on the electricity bill as well as the water bill.
Q: Can I still use hot water while I wait for a plumber? A: If the leak is visible and serious, keep the geyser off and its supply closed. If you suspect a slow hidden leak, you can use the geyser, but book an inspection soon, because the leak will cost more and may damage floors or walls the longer it runs.
Q: Can you find a hot-water leak under tiles without lifting them? A: Yes. Thermal imaging and acoustic equipment locate the leak through the tiles, and only the tiles directly above it need to be lifted for the repair.
